122
MICROPHONE
STANDS
STANDARD DESKTOP ADJUSTABLE
MICROPHONE STAND
This is all-time standard desktop style, a 5-1/4”
diameter, round, die-cast iron base (black finished)
with an adjustable chrome shaft. Height may be
adjusted from approximately 7.5 to 13.5 inches.
Sure-locking Collett prevents slipping and will last
indefinitely. Standard 5/8”-27 threads at top accepts
threaded microphone holders.
No. 71-4512
………..Standard desktop mike stand
DELUXE DESKTOP
MICROPHONE STAND
with BOOM
For very serious use, such as interviews, recording commercials or radio work, this is a fine stand with several very
important features. The boom is removable if there are occasions to use the stand and shaft alone; height adjusts
from about 9” to 15” and will accommodate any standard 5/8”-27 microphone holder (not included). The boom is 17”
long and may be adjusted “in” or “out” as well as set at any angle necessary; a secure cam will hold a microphone
exactly where you place it. The die-cast iron base is nicely finished (soft black) and has rubber feet to prevent mar-
ring table surfaces. May be silently readjusted/repositioned for changing users. Heavy, not usually recommended for
portable use. This is a professional quality microphone stand and priced far below professional cost.
No. 71-4517
…………….Deluxe desktop Microphone Stand w/boom.
DESKTOP STOWAWAY MICROPHONE
STAND
It looks like a miniature space probe
when collapsed for travel, but it’s
actually a tough little stand that can
be set up in a few seconds. The leg
assembly unscrews from the upper
cone assembly and the legs collapse
and store inside. Made of a tough,
fiber filled plastic. Reduces to a 5-
1/4” long cone. Standard 5/8”-27
thread on top, accommodates stan-
dard microphone holders.
Part no. 71-4503
…..
Stowaway mike stand.
DESKTOP TRIPOD
MICROPHONE STAND
A very portable little stand that will
accommodate any microphone holder
that has a standard 5/8”-27 thread.
The legs may be collapsed for
easy storage and protected transport;
sets up again in seconds. Chrome fin-
ish and soft rubber feet.
No. 71-4502
...
tripod desktop stand
STANDARD MICROPHONE FLOOR
STANDS
This is a familiar microphone stand with die-cast
iron base and adjustable in height. The upright
may be adjusted from approximately 32” in height
up to 60”. (The addition of a microphone and hold-
er will usually take the mike up to about 5-1/2 feet
max. height) The 5/8”-27 thread on top will accom-
modate standard microphone holders. Heavy
rubber feet eliminate floor noise; and positive lock-
ing collets assure that the height will stay where
you have placed it.
Two finishes are available, traditional chrome mir-
ror finish shaft with a black base or non-reflective
black shaft and base.
No. 71-4652
……..Floor Stand, Chrome
No. 71-4653
…….Floor Stand, all Black
TRIPOD MICROPHONE FLOOR
STANDS
An innovative idea in microphone stands, light in
weight and collapsible for easy transport or stor-
age. The stand may be adjusted from a height of
only 31” up to 64” and is very stable. The col-
lapsed package is only 31” long; easy to trans-
port and much lighter than die-cast base units.
The top accommodates standard (5/8”-27
threads) microphone holders. Constructed of
steel tubing and nylon molded parts. Rubber
feet.
Two finishes are available, traditional chrome
mirror finish shaft with black molded parts; or
non-reflective black shaft and black molded
parts. (Black for low reflection of spotlights and
camera flash units.)
No. 71-4682
……..Floor Stand, Chrome
No. 71-4683
…….Floor Stand, all Black
DESKTOP GOOSENECK
MICROPHONE STAND
An iron, die-cast base and flexible gooseneck
microphone stand. Rubber feet and a vinyl
clad base provide for quiet use. The 5/8”-27
thread on top accommodates standard micro-
phone holders. The entire stand is a low
reflecting black finish. The gooseneck may be
unthreaded from the base for transport or use
with other stand parts. Total height 13.5”
No. 71-4507
- Gooseneck mike stand, black
OFC...,112,113,114,115,116,117,118,119,120,121 123,124,125,126,127,128,129,130,131,132,...352