164
BAND SEPARATORS, SPLITTERS
....perfectly designed and matched for TV and FM signals
coming from the UHF-VHF-FM BANDS. Heavy duty wire and
cable prevents broken connections. Non-strip piercing
screws are made of plated brass for corrosion-free reliability.
Add suffix letter “B” to part number for bulk pack.
No. MT77
75-300 OHM BALUN
WITH UHF/VHF/FM SPLITTER
Matches impedance between 75
ohm coaxial cable and 300 ohm
TV and FM antenna inputs. It sep-
arates the three signals from the
3-way antenna into individual sig-
nals for UHF, VHF and FM. Two
outputs connect to the UHF, VHF
antenna terminals on rear of the TV set. Separate screw terminal
connects 300 ohm twin lead to the FM receivers. For VCR’s too.
No. MT78
75-300 OHM BALUN AND
UHF/VHF/FM BAND SEPARATOR
Separates incoming signals from
a 75 ohm antenna downlead into
UHF, VHF and FM bands. The
coaxial 75 ohm cable is fitted
with an “F” connector to accom-
modate the VHF terminal on rear
of TV set or VCR. The 300 ohm output for UHF connects to the
receiver with heavy, hook terminated wires.
No. MT88
75 ohm VHF + 300
ohm UHF to 75 ohm
push-on male.
No. CA280
300 OHM JUMPER CABLE
300 ohm cable, twin lead, with spade lug on both ends for extension lead
between VCR and TV, 6ft.
SEPARATOR/COMBINER BALUNS
Designed expressly for TV sets with “F” coaxial jack input, these baluns will accept
75 ohm coax or 300 ohm twin lead input and combine them, feeding them to the
set through a push-on “F” connector on the back of each type. These combiners
may be used as separators because they can function with signal fed in either
direction. Individually packaged for display rack, they may be obtained bulk
packed by adding suffix letter “B” to the part number
.
(Back View)
No. MT86
75 ohm VHF + 75 ohm
UHF to 75 ohm
push-on male.
No. MT87
300 ohm VHF + 300 ohm
UHF to 75 ohm
push-on male.
VIDEO AMPLIFIERS & SPLITTERS
UHF/VHF/FM HIGH GAIN DISTRIBU-
TION AMPLIFIER (with FM TRAP)
No. DA27B
Traps out
strong FM
interference
from TV.
SPECIFICATIONS:
Band Width:
50 to 900 Mhz.
Output Capability:
40 dbmV
Gain:
VHF-25db, UHF - 21db
Noise Figure:
4 db
FM Trap Attenuation:
-20 db (switchable) 95 - 108 MHz.
Input:
75 ohm, “F” type coax connector
Output:
75 ohm, “F” type coax connector
Power Source:
120VAC 60Hz
Dimensions:
3” x 5 7/8” x 1-5/8”
10 db VCR/TV SIGNAL AMPLIFIER
50-900MHz
6 db VCR/TV SIGNAL AMPLIFIER
with 2 OUTPUTS 50-900MHz
10 db VCR/TV SIGNAL AMPLIFIER
with 4 OUTPUTS 50-900MHz
Sharpens and improves pic-
ture quality by restoring signal
loss that occurs in some 75
ohm connections. Standard
“F” connectors; 117 volt @
1.2 watt operation. Boosts
both TV and FM radio sys-
tems.
No. DA10B
Single 75 ohm input from
antenna or cable system
with two 75 ohm outputs.
Standard “F” connectors;
117 volt @ 1.2 watt (10mA)
operation.
No. DA12B
Single 75 ohm input from
antenna or cable system
with four 75 ohm outputs.
Standard “F” connectors;
117 volt @ 1.2 watt (10mA)
operation.
No. DA14B
*ALL PHILMORE Signal Amplifiers cover to 900 MHz and can be
used to amplify cable signal.
c
US
OFC...,154,155,156,157,158,159,160,161,162,163 165,166,167,168,169,170,171,172,173,174,...352