266
TERMINAL BLOCKS & KNOBS
TERMINAL BLOCKS
A terminal block designed to be end-stackable on a PC board so that the
designer may have any number of contacts needed. The design provides
secure wire protection for a broad range of wire sizes (up to 14 ga. max).
The housing is molded of 94V-0 fire retardent plastic. Six pieces per pack-
age; available in bulk, add “B” suffix to part number. (i.e. TB132B for Bulk)
Housing: Polymide 66 resin, blue
Terminals: 0.9 x 0.9 Brass, tin plated
Screws: M2.6 x 0.45P, steel, zinc plated
Wire cage: Brass, Nickle plated
Rated: 10 Amp. 300 VAC
Temperature rating: -55°C to + 125°C
Wire range: 14 AWG max.
Dielectric Strength: 2000 VAC min.
for 1 minute
Insulation Resistance: 500 M ohm min.
at 500 VDC
Pitch: 5 mm
Number of pole: 2, 3
STRAIGHT TYPE
RIGHT ANGLE TYPE
No. TB132 – 2 Pos. Pkg./6
No. TB142 – 2 Pos. Pkg./6
No. TB133 – 3 Pos. Pkg./6
N0. TB143 – 3 Pos. Pkg./6
Fluted with skirt
indicator line on top
.75” Dia., .50” High
Color: Black
No. 3010
Fluted with taper skirt
indicator line on top
.94” Dia., .60” High
Color: Black
No. 3035
Straight knurl with arrow
head indicator on top
.82” Dia., .50” High
Color: Black with Aluminum
top inlay
No. 3055
Straight Knurl 0-9 num-
bers on
aluminum skirt
1.15” Dia., .70” High
Color: Black with
Aluminum top inlay
No. 3020
Straight knurl 0-10 num-
bers on
aluminum skirt
1.46” Dia., .60” High
Color: Black with
Aluminum top inlay
No. 3045
Control pointer knob with
indicator line on top & side
1” Dia., .60” High
Color: Black
No. 3050
Straight knurl pointer indi-
cator line on side pointer
.54” Dia., .48” High
Color: Black with Aluminum
top inlay
No. 3060
Fluted grip with
indicator line
Color: Black with Aluminum
top inlay
.60” Dia., .46” High
No. 3025
.92” Dia., .62” High
No.3030
Ribbed with skirt
indicator line
Color: Black with
Aluminum top inlay
.80” Dia., .67” High
No. 3015
1.35” Dia., .86” High
No.3040
KNOBS
Black bakelite material, brass insert for 1/4” shaft with set screw.
SPECIFICATIONS
Black pointer knob with
indicator line. 1.25” long
No. 277AP
Straight knurl, aluminum
skirt with black indicator
arrow. 1.375” DIA., .56” high
Color; Black with aluminum
top inlay.
No.337
For bulk pack add suffix letter “B”
Precision Tuning
VERNIER DIAL CONTROL KNOBS
A vernier dial control knob will provide smooth and precise
tuning for either a potentiometer or variable capacitor.
Planetary drive provides 8 to 1 ratio, allowing for very fine
adjustment of standard controls. The metal dial plate is cali-
brated by etching and paint filling on brushed satin finish for
a very attractive appearance. Knob is calibrated over 180
degrees of turn, reading from zero to maximum setting by
clockwise rotation. Fits standard 1/4” control shafts and
mounts on surface of cabinet or chassis. Very useful with
any circuit where fine “tuning” is going to make life easier.
Part no.
Diameter Calibration
S36
1 1/2”
0 to 10
S38
1-1/2”
0 to 100
S50
2”
0 to 100
No. S50
Rear View
No. S36
No. S38