TELEPHONE JACKS, various & modular type
PART OF PHILMORE’S TELEPHONE ACCESSORIES
INCLUDE WALL PLATES. FOR OTHER TELEPHONE ACCESSORIES,
PLEASE CONSULT THE PHILMORE INDEX PAGE UNDER THE TELEPHONE CATEGORY.
NOTE: IDC 110 type jacks at bottom of this page. And ordinary surface-mounting jacks here.

NOTE: Philmore wall plates are always supplied with mounting screws of a matching color.

Round MODULAR PHONE JACK

A 3-1/4" diameter jack assembly that may be mounted on any flat surface. Available in either four or six conductor. Wires connect at screw terminals. A mounting bracket is included, unless specified otherwise.

MODULAR FLOOR JACK ASSEMBLY

The floor jack fits a standard electrical box, and standard single hole type AC outlet wall plates. We do not have the plate; find it at your local hardware box store. The plate willhave one large round hole in the center that matches this jack. We suggest steel or another durable metal for a floor plate.

Part no. TWP66B Floor jack assembly (bulk packed only, no display card).

Part no. TWP66NB Floor jack with NO mounting bracket (bulk pack only).

SEE FLOOR MOUNT JACK WITH 110 IDC TERMINALS BELOW

WALL PLATE MOUNTING BRACKETS
If you want to mount a wall plate, and avoid installing an electrical outlet box , then one of these brackets can be a quick solution while still providing a solid mount.
=======

LOW VOLTAGE WALL PLATE BRACKET

Called "low voltage" as it is intended for use with telephone or computer plates, and is not appropriate for 115 volt AC sockets.

Used mostly during New construction, the bracket is intended to be mounted on a stud, with dry wall over the bracket. Then the wall plate is mounted on this bracket.

Part no. 72-4102B New Construction low voltage bracket.
(distributor note; unit is supplied only in bulk, not in display package.)

==========

Retrofit LOW VOLTAGE WALL PLATE BRACKET

The bracket is for use in EXISTING construction; by cutting a hole in the wall and then bending the tabs on this bracket to secure it. The wall plate can then be mounted to the bracket and it will be a secure installation .

Part no. 72-4100B Retrofit Bracket

bulk packed only

BLANK WALL PLATES
for your own connectors and design ideas.

High-impact thermoplastic and non-flammable, Philmore blank wall plates meet all UL and CSA requirements. Each is supplied with matching color mounting screws, and fits a standard electrical outlet box or the brackets above. Available in all standard colors in single width; also available double wide in two popular colors.

                Note; blank Designer Wall Plate Inserts are also available.
                BLANK STAINLESS STEEL WALL PLATES ARE HERE.

Single wall mount jack...follow link.

TELEPHONE AND DATA JACKS WITH
IDC 110 TYPE CONNECTORS

This series is popular with professional installers, a fast installation that is also reliable is possible for experienced users. The series meets Level 3 and 4 requirements. Recommended for use with 22 to 26 AWG wire (either stranded or solid). All contacts have a minimum of 30 micro inches of gold plating and plastics are UL94V-0 rated ABS. UL no. E134135 and CSA listed LR90192 circuit accessory 82X6. The entire series is available only in IVORY.

SINGLE FLOOR MOUNT JACK
with IDC 110 type Connections.
Note: 6p6c means "six position, six contacts" etc.

Part no. 75-5160 6p6c Single Jack, ivory
Part no. 75-5180 8P8C Single Jack, ivory

all of this series in IVORY only.

                                        SINGLE SURFACE or
WALL MOUNT JACK
with IDC 110 type Connections.
Note: 6p6c means "six position, six contacts" etc.
 

Part no. 75-5460  6p6c Wall Jack, Ivory
Part no. 75-5480 8p8c Wall Jack, Ivory

all of this series in IVORY only.

DUPLEX FLOOR MOUNT CONNECTOR
with IDC 110 type Connections.
Two jacks each block, for either voice or data.
Note: 6p6c means "six position, six contacts" etc. and 8p8c means "eight position, eight contacts".

Part no. 75-5266  two 6p6c jacks
Part no. 75-5268 one 6p6c and one 8p8c KEYED
Part no. 75-5288  two jacks, 8p8c, both keyed. 

all of this series in IVORY only.

DUPLEX SURFACE MOUNT 
with IDC 110 type Connections.
Two jacks each block, jacks marked voice and data.

all of this series in IVORY only.

Part no. 75-5466  Two 6p6c Jacks
Part no. 75-5468 One 6p6c & one 8p8c keyed.
Part no. 75-5488 Two keyed 8p8c jacks.

For other types of Wall Plates, be sure to see the Index page here.)

link back to Philmore New Products 2006 Index page.
Link to the Philmore-Datak Home page.
Link to the Philmore Index page

PHILMORE MANUFACTURING COMPANY is a division of LKG INDUSTRIES Inc. of Rockford, Illinois
all pages are copyright LKG Industries Inc. and may not be reproduced without permission.