PHILMORE

Category 5 WALL PLATES and Network Products for DATACOM.
For CAT5 RJ45 CONNECTORS (plugs), this is the link to
that page.

Part no. CAT5001 Wall Plate |
Part no. CAT5002 Wall Plate |
Part no. CAT5003 Wall Plate |
Part no. CAT5004 Wall Plate |
Part no. CAT5006 Wall Plate |
This series of Wall Plates will accommodate a variety of
jacks, which will fit into snap-in inserts which are shown below. A combination
of jacks may be used, which the user determines by using his choice of inserts.
NOTE that this series is available only in WHITE.
The series shown here are NOT Keystone openings, those are listed below. The
CAT5000 series uses its own set of inserts which are shown just below the wall
plates.
NOTE: Designer style wall plate
inserts and plate covers are available here. These are Keystone type plates
as well as all of our Designer plates.
BE SURE TO CHECK THE WALL PLATE INDEX to see all
of the varieties available to you.
For
CAT5 RJ45 CONNECTORS, this is the link to that page.

INSERTS for the
above WALL PLATES
For use with the CAT5 Wall Plates, the user may select inserts to accommodate
any choice of fiber optic, coaxial cable connectors or for Keystone Jacks to
accommodate 8-pin RJ-45 data jacks etc. The Keystone inserts are available in
the standard EIA/TIA specified colors. The blank insert is intended for use to
hold a position for a future connector that is not needed or known at time of
installation.
Part no. CAT5020
|
Part no. CAT5025 |
Part no. CAT5030 |
Part no. CAT5035 |
Part no. CAT5040* |
Insert side view |
|
|
|
|
|
|
Blank Insert |
F-81 "F" Connector Insert |
TNC/BNC Insert |
ST Fibre Optic Insert |
Keystone Insert, see colors
below* |
a general idea of how all inserts look from
the side. |
*The CAT5040 series KEYSTONE Inserts are available in colors;
chose the part numbers from the following chart.
Part No. |
Keystone insert color |
CAT5040 |
Black Keystone Insert |
CAT5045 |
BLUE Keystone Insert |
CAT5050 |
GREEN Keystone Insert |
CAT5055 |
RED Keystone Insert |
CAT5060 |
WHITE Keystone Insert |
CAT5065 |
YELLOW Keystone Insert |
SNAP-IN ICONS for KEYSTONE INSERTS
Shown at your left in enlarged size; A series of snap-in ICONS that can
help to keep which Keystone jack is "what". Depictions of a phone, computer
terminal or the word CAT5 can help the user know which jack he needs to plug
into. Four each of Voice, PC and CAT5 Icons in this package:
PART NO. CAT5200 snap-in icons pack.

KEYSTONE WALL
PLATES for DATACOM
category 5 as well as TV, RF
and other connectors
The Keystone wall plate series shown below is a series with .58" x .76"
openings that accept Keystone Jacks without the need of any special inserts. A
variety of CATEGORY 5 jacks are available for this series of wall plates and for
TV F-connectors, S-video, BNC connectors and more are available to fit
into the same Keystone size opening in this series of wall plates.
THE KEYSTONE WALL PLATES
|
Single Hole Keystone wall
plate, accommodates any Keystone size jack or insert.
Part no. 75-5011 IVORY
Part no. 75-5019 WHITE |
|
Two Hole Keystone wall
plate, accommodates any Keystone size jack or insert.
Part no. 75-5021 IVORY
Part no. 75-5029 WHITE |
|
Three Hole. Part no.
75-5031 IVORY
Part no. 75-5039 WHITE |
|
Four Hole Part no.
75-5041 IVORY
Part no. 75-5049 WHITE
|
|
Six Hole
Part no. 72-5061 IVORY
Part no. 72-5069 WHITE
|
Jacks and inserts below.
See the DESIGNER STYLE Plates if you prefer that
style and appearance.
INSERTS for the ABOVE KEYSTONE
WALL PLATES
BNC INSERTS
Part no. 72-5013 IVORY
Part no. 72-5014 WHITE |
"F" CONNECTOR INSERTS
Part no. 72-5015 IVORY
Part no. 72-5016 WHITE |
BLANK INSERTS for
drilling any custom hole you wish. Part no. 72-5017 IVORY
Part no. 72-5018 WHITE |
|
|
|
The KEYSTONE JACKS and jack parts
CAT3 Voice Grade Jack
A jack for us4e with telephone systems, facsimile machines
and other voice grade equipment. Fits the Keystone cutout; compatible with
AMP, Hubbell, Kron, ICC etc. The jacks accept 22-26 AWG solid or stranded
wire.
All are six conductor jacks.
Part no. 72-3060 BLACK
Part no. 72-3061 IVORY
Part no. 72-5014 WHITE |
Tool-less CAT5 JACKS
A punch-down tool is not needed; hinged cover, when
snapped closed, forces the wire connection. This series have been tested
to meet EIA/TIA 568A&B, TSB40A specs. May be used (backward compatible)
with CAT3&4. Use with 22-26 AWG wire.
Part no. 72-5070 BLACK
Part no. 72-5071 IVORY
Part no. 72-5079 WHITE |
METAL SHIELD for
KEYSTONE JACKS
An optional shield for high noise areas or
for use with shielded (STP) cable. A two piece unite that snaps around the
jack after the cable has been attached and jack is in location.
Part no. CAT5110 |
|
|
|

110 STYLE JACKS
A series of jacks that fit
KEYSTONE size openings in plates and adaptors. The 110 series requires
connection using a "punch-down" tool for the best job. All of these jacks meet
EIA/TIA 568A&B as well as TSB40 standards for Enhanced Category 5 use. These
jacks may be used "backward compatible" in older systems such as CAT4 and CAT 3
in addition to CAT5 and CAT5e.
|
180°
CAT5e Jack; constructed of UL 94VO plastic and has 50 micro
inches of gold on contacts. A 180° Jack has contacts that
are at a right angle to the front of the jack. Accepts wire in range of
22-26 AWG. A 110 punch down connections jack.
Part no. 72-5500 eight conductor BLACK
Part no. 72-5501 eight conductor IVORY
Part no. 72-5509 eight conductor WHITE |
|
90°
CAT5e Jack; constructed of plastic and PCB. A 110 punch down connections
jack. Part no. 72-5000 eight conductor
BLACK
Part no. 72-5001 eight conductor IVORY
Part no. 72-5009 eight conductor WHITE |
|
90°
CAT5e ENHANCED Jack. Meets all CAT5e specs and will handle up to 350Mhz
! Gold contacts, of course; fits KEYSTONE knockout hole. A 110 punch down
connections jack. Part no. 72-5580 eight
conductor BLACK
Part no. 72-5581 eight conductor IVORY
Part no. 72-5589 eight conductor WHITE |
ECONOMY 110 TYPE PUNCH DOWN TOOL
OK for the casual user, an expensive plastic tool for use in
"punching-down" wires
into the contacts of 110 style connectors. Provides a very solid connection and
works well with the above jacks and other 110 products.

CATEGORY 5e FEED-THRU JACK
Snaps into a standard KEYSTONE opening; has an RJ-45 size, eight conductor
jack on each side. Use with any Keystone style wall plate above or with Keystone
type inserts.
Part no. 70-5128 CAT 5e Feed thru Jack.

S-VHS FEED-THRU JACK
for use in Keystone wall plates
A standard 4-pin mini-DIN on each side for use with Home Theartre equipment.
The Jack fits any KEYSTONE size opening in above plates or insert adaptors.
Part no. 70-478 S-VHS feed thru jack (WHITE)

For CAT5 RJ45 CONNECTORS, this is the link to that
page.

VOICE GRADE FEED-THRU JACK
Female RJ-45 on each end, could also be used in line as a coupler. Fits
the standard Keystone plates and inserts above. UL listed and 50 microns gold on
contact surfaces.
Part no. CAT5126 Six conductor (6p6c) Jack
Part no. CAT5128 Eight conductor (8p8c) Jack

ELECTRICAL OUTLET COMPATIBLE
KEYSTONE WALL PLATES.
Either insert fits in a standard electrical outlet box and is made for use
with Keystone Jacks and standard electrical wall plates as covers. (Wall plates
are very low cost at any hardware store.) Use any of the Keystone snap-in jacks
above.
May be used in ordinary applications or in floor mounting boxes etc. Available
in WHITE only. Mounting screws supplied.
Part no. 72-5089 Single Keystone hole
Part no. 72-5099 Dual Keystone holes.

|
DESIGNER STYLE CAT5e
Wall Plates with jacks installed.
Preassembled wall
plates that fit the popular "DECORATOR" style wall plates that are quite
popular now. White is the only color available.
Part no. CAT5111
Plate with one RJ-45 jack
Part no. CAT5112 Plate with two RJ-45 jacks
Mate with 75-1000
and 75-2000 covers above. |
|
NOTE: Philmore wall plates are always
supplied with mounting screws of a matching color.

CAT5e SURFACE
MOUNTING JACKS (350MHz)
CAT5e surface mount jacks provide for a fast and easy
installation. May be used with older (CAT5, CAT4 etc.) systems and equipment.
All units are UL listed and certified to meet the EIA/TIA 568A & B as well as
TSB40A specifications.

Shown above, the
72-5521 Dual jack and to your right above, the single jack 72-5511
Part no. |
DESCRIPTION |
72-5511 |
Single RJ45 8C Jack; ivory color |
72-5519 |
Single RJ45 8C Jack, white color |
72-5521 |
Dual RJ45 8C jacks, ivory color |
72-5529 |
Dual RJ45 8C jacks, white color |

For
CAT5 RJ45 CONNECTORS, this is the link to that page.
Link back to the
Wall Plates Index page.
link back
to Philmore New Products 2006 Index page.
Link to the
Philmore-Datak Home page.
Link to the Philmore Index page
PHILMORE MANUFACTURING COMPANY is a
division of LKG INDUSTRIES Inc. of Rockford, Illinois
all pages are copyright LKG Industries Inc. and may not be reproduced without
permission.
|