link back to Philmore New Products 2006 Index page.
link back to floor stands
DESKTOP MICROPHONE STANDS
and miscellaneous Accessories.
STANDARD DESKTOP adjustable
MICROPHONE STAND
This is all-time standard desktop style, a 5-1/4" diameter, round, die-cast iron base (black finished) with an adjustable chrome shaft. Height may be adjusted from approximately 7.5 to 13.5 inches. Sure-locking Colet prevents slipping and will last indefinitely. Standard 5/8"-27 threads at top accepts threaded microphone holders.
No. 71-4512………..Standard desktop mike stand
Desktop STOWAWAY MICROPHONE STAND
It looks like a miniature space probe when collapsed for travel, but it’s actually a tough little stand that can be set up in a few seconds. The leg assembly unscrews from the upper cone assembly and the legs collapse and store inside. Made of a tough, fiber filled plastic body with steel legs.. Reduces to a 5-1/4" long cone. Standard 5/8"-27 thread on top, accommodates standard microphone holders.
Part no. 71-4503…..Stowaway mike stand.
DESKTOP TRIPOD MICROPHONE STAND
A very portable little stand that will accommodate any microphone holder that has a standard 5/8"-27 thread. The legs may be collapsed for easy storage and protected transport; sets up again in seconds. Chrome finish and soft rubber feet.
No. 71-4502…tripod
desktop stand
Desktop GOOSENECK
MICROPHONE STAND
An iron, die-cast base and flexible gooseneck microphone stand. Rubber feet and a vinyl clad base provide for quiet use. The 5/8"-27 thread on top accommodates standard microphone holders. The entire stand is a low reflecting black finish. The gooseneck may be unthreaded from the base for transport or use with other stand parts. Total height 13.5"
No. 71-4507 – Gooseneck mike stand, black
DELUXE DESKTOP
MICROPHONE STAND with BOOM
For very serious use, such as interviews, recording commercials or radio work, this is a fine stand with several very important features. The boom is removable if there are occasions to use the stand and shaft alone; height adjusts from about 9" to 15" and will accommodate any standard 5/8"-27 microphone holder (not included). The boom is 17" long and may be adjusted "in" or "out" as well as set at any angle necessary; a secure cam will hold a microphone exactly where you place it. The die-cast iron base is nicely finished (soft black) and has rubber feet to prevent marring table surfaces. It’s Heavy! The boom and shaft may be silently readjusted/repositioned for changing users. Very Heavy, not usually recommended for portable use. This is a professional quality microphone stand and priced far below professional cost.
No. 71-4517
…………….Deluxe Microphone Stand w/boom.
FLANGE-style MICROPHONE MOUNTS
Designed for mounting on a table top, side wall etc., will accommodate a gooseneck or microphone extension pipe. Made for use as a permanent mount. The larger diameter is suggested for better strength if use will be constant and rigorous. Chrome plated finish; 5/8-27" standard threads.
part no. 71-4001 – 1-3/4" diameter, male threads
part no. 71-4005
– 2-3/4" diameter, male threadspart no. 71-4007
– 2-3/4" diameter, female threads
"MIKE PIPE"
Use with the flange mounts (No. 71-4007) with bases for table microphone stands etc.. The 3" "pipe" is chrome plated, threaded on each end with standard 5/8"-27 threads to mate with standard microphone holders and bases. Included is a star nut that can be used to tighten the pipe against a mike holder, prevents loosening.No. 71-4010………….3" Mike Pipe
MICROPHONE HOLDER ADAPTORS
Microphone holders and stands are supplied with one of two different size threads. The 5/8" -27 size is the standard with our stands and the other common size thread is smaller: 3/8"-17. If you have a mike holder of one size and a stand with the other, you’ll need an adaptor to use them together. One of these small adaptors will solve the problem; and road groups should always carry a few of each
71-4015
– 3/8"-17 female to 5/8"-27 male (left photo)71-4016
– 5/8-27 female to 3/8" -17 male (right photo)
Flexible "gooseneck" may be used with Flange mounts, table top stands or on top of a floor microphone stand. The completely flexible neck provides quick, easy repositioning of the microphone. Available in two lengths and in standard chrome or dull, non-reflective black. Male one end, female on the other. Chrome is the old standard; black is best when taking pictures or videos of performers.
71-4030
– 6" length Gooseneck, black71-4031 – 6" length Gooseneck, chrome
71-4040 – 13" length Gooseneck, black
71-4041 – 13" length Gooseneck, chrome
This adjustable microphone holder adapts to the bodies of microphones from small cassette types to larger professionals. A squeeze of the handle, and the holder grips the microphone with a secure grooved ridge contact. Accommodates microphone handles from 5/8" to 1-3/8" diameter. Tilts a full 180 degrees. Standard microphone stand fittings, 5/8" – 27 threads.
No. SM85
MediaStar
MICROPHONE HOLDER
A standard microphone holder that will fit all microphone stands that have a 5/8-27" thread (all Philmore stands inclusive). Accommodates the MediaStar microphones and other major brands that have a diameter of about 1-3/4 inches.
No. 71-1599
Holds microphone firmly – No Compromise Slide in any microphone having a 3/4" to 1- 1/4" diameter handle. This black holder is sharp looking with all microphones. Firm swivel adaptor tilts through 180 degrees. Has standard 5/8" – 27 threads, which fit all Philmore and other brands of standard microphone stands.
Part No. SM70 UNIVERSAL MICROPHONE HOLDER
Have you seen the fine
MediaStar Microphones from Philmore?Here is a link to see them:
Microphones, MediaStar® microphones
We sincerely believe that the MediaStar microphones are the finest value that you can find in low-cost, high quality microphones.
link back to Philmore New Products 2006 Index page.
link back to Philmore-Datak home page
Home Page
PHILMORE MANUFACTURING COMPANY is a
division of LKG INDUSTRIES Inc. of Rockford, Illinois
all pages are copyright LKG Industries Inc. and may not be reproduced without
permission.